The Team Durango DESC10 was an absolute pleasure to drive. I felt right at home driving this truck and literally, this was the first time driving this truck on this video. With a completely stock set up from the manual, the truck really performed and will need little to no adjustments to be super dialed.
BIG Thanks to Tom and Mario from The Yard RC Track in Orange, CA for giving The RCNetwork private access to film on the track. Check em out on FaceBook:
Want to see how the DESC10 built up? Check out this video:
Here's where I got the DESC10 and how it's outfitted:
Here's the items I selected:
Team Orion R8.1 Pro ESC:
Team Orion VST2 690 Motor:
Futaba BLS371 Servo:
Pro-Line HoleShot 2.0 Tires:
Pro-Line Flotek Body: /
DE Racing Trinidad Wheels:
After building the new DEX8T 1/8th scale Truggy, I was really amazed at the over all build experience with the pre-assembled components. The new DESC10 is of the same mold, but in 1/10th scale ShortCourse fashion. the new Team Durango line of KIT's cut down the building time by at least 50% and the quality of parts and assembly are top quality.
With an all new design, the DESC10 is part of the new evolution of 4WD SCT's incorporating 1/8th scale components to drive up the durability scale. With an all new Motor mount design, capable of 550 or 1/8th scale motor, highly tunable with the included tuning blocks, ability to change a diff in right over a minute (less than a minute on the buggy!) and 17mm wheel hubs.
Check out my FaceBook page for up to the minute status on this and many other projects going on at the The RCNetwork:
Here's where got it and some info from Team Durango:
/
Chassis: Hard anodized 7075 T6 aluminum, 0.12" (3mm) thick
Drive: Four wheel shaft with center U-joints for maximum drivetrain
efficiency and minimal heat transfer, rear mud guards help keep
drive shafts clean
Shocks: 16mm Big Bore aluminum body with vented caps, and a choice of
constant volume and emulsion bodies
Shock Towers: 0.20" (5mm) thick aluminum
Suspension: Fully adjustable pivot ball with square hinge pin inserts
for more options for front end mods, galvanized components for
protection against oxygenation, Active Caster Inserts for easy
configuration changes
Differentials: Ultra lightweight bevel gear type with composite cross
shafts for increased acceleration and durability
Motor Mount: Aluminum, with step-down washers for secure mounting for
550 size motors as well as traditional 550 size SC motors
Steering: Servo saver and ball bearing equipped, also has adjustable
Ackermann, Ackermann refers to the effect of inner front wheel
rotating faster than the outer front wheel during turns
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
INCLUDES
DESC10 Short Course Truck Kit with Shocks, Decal Sheet, Adjustable
Motor Mount and Instructions
REQUIREMENTS
Radio: 2-channel with high-torque steering servo
Motor: 550-size, or larger 1/8 scale brushless motor
Pinion Gear: 48P, number of teeth compatible with selected motor
LiPo Battery: 2S 7.4V, at least 5000mAh
Battery Charger: Compatible with selected batteries
Tires: 1/10 scale short course
Wheels: 1/10 scale short course
Body: 1/10 scale short course truck
Charging bag, building and track equipment, silicone shock and diff
oil
SPECIFICATIONS
Length: 21.5" (546mm)
Width: 11.6" (294mm)
Height: 7.5" (190mm) approximately
Weight: 7.5lbs (3.4kg) depending on electrical items installed
Wheelbase: 12.7" (324mm)