How to Bore for a New Door Knob | Ask This Old House
Ask This Old House general contractor Tom Silva helps a homeowner install a new passage set door knob on his closet door
SUBSCRIBE to This Old House:
Time: 1 hour
Cost: $90
Skill Level: Easy
Tools List for Boring for a New Door Knob:
Drill/Driver
2 1/8” Hole Saw
1” Hole Saw
Hole Saw Jig
Screwdriver
Chisel
Pencil
Shopping List:
Passage Set
Steps:
1. Place the hole saw jig on the door. Position it three feet off the ground. Set the backset measurement to either 2 3/8” or 2 _”, depending on the style of the door and personal preference.
2. Use a drill/driver with the 2 1/8” hole saw to bore a hole through the door. Once the center bit is through the door, stop. Bring the hole saw the other side of the door and finish the bore.
3. Use the 1” hole saw to bore a hole through the edge of the door to create an area for the latch.
4. To make room for the latch plate, place the latch plate on the edge of the door and draw an outline. Use a chisel to remove the wood inside the outline. Seat the latch plate into the edge to make sure it fits properly.
5. With the latch plate seated, install it using screws and a screwdriver.
6. Install the door knobs to the front and the back of the door. Line up both pieces and attach them through the latch. Use screws and a screwdriver to fix them in place.
7. If necessary, mortise out the jamb for the striker plate. Outline the plate and line it up with the striker. Use a chisel to mortise the outline.
8. Use screws and a screwdriver to attach the striker plate.
About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.
Follow This Old House and Ask This Old House:
Facebook:
Twitter:
Pinterest:
Instagram:
Tumblr:
For more on This Old House and Ask This Old House, visit us at:
How to Bore for a New Door Knob | Ask This Old House
/
SUBSCRIBE to This Old House:
Time: 1 hour
Cost: $90
Skill Level: Easy
Tools List for Boring for a New Door Knob:
Drill/Driver
2 1/8” Hole Saw
1” Hole Saw
Hole Saw Jig
Screwdriver
Chisel
Pencil
Shopping List:
Passage Set
Steps:
1. Place the hole saw jig on the door. Position it three feet off the ground. Set the backset measurement to either 2 3/8” or 2 _”, depending on the style of the door and personal preference.
2. Use a drill/driver with the 2 1/8” hole saw to bore a hole through the door. Once the center bit is through the door, stop. Bring the hole saw the other side of the door and finish the bore.
3. Use the 1” hole saw to bore a hole through the edge of the door to create an area for the latch.
4. To make room for the latch plate, place the latch plate on the edge of the door and draw an outline. Use a chisel to remove the wood inside the outline. Seat the latch plate into the edge to make sure it fits properly.
5. With the latch plate seated, install it using screws and a screwdriver.
6. Install the door knobs to the front and the back of the door. Line up both pieces and attach them through the latch. Use screws and a screwdriver to fix them in place.
7. If necessary, mortise out the jamb for the striker plate. Outline the plate and line it up with the striker. Use a chisel to mortise the outline.
8. Use screws and a screwdriver to attach the striker plate.
About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we're ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O'Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.
Follow This Old House and Ask This Old House:
Facebook:
Twitter:
Pinterest:
Instagram:
Tumblr:
For more on This Old House and Ask This Old House, visit us at:
How to Bore for a New Door Knob | Ask This Old House
/
Rcreviews.lt is not the owner of this text/video/image/photo content, the real source of content is Youtube.com and user declared in this page publication as Youtube.com user,
if you have any question about video removal, what was shared by open community, please contact Youtube.com directly or report bad/not working video links directly to video owner on Youtube.com. Removed video from Youtube.com will also be removed from here.
Advertising