X-Uav Talon FPV Plane - Second flight and some Mavic Air clips
X-UAV Talon EPO 1718mm Wingspan V-tail white version FPV flying Glider RC Model Airplane.
Morten was in a bit hurry so he forgot the canopy and the wires for he's home made and 3D printed gimbal so this flight is just to test out all the stuff he has mounted inside the plane.
Mortens setup:
X-UAV Talon specs:
1718mm wingspan
1100mm length
Usable flying weight up to 5kg. Would not recommend handlaunch over 3,5kg
Motor Sunnysky 3525 880kv with 12x6 propeller. Powered by a 5x4 (5S-4P) Panasonic NCR18650B LiIon batteries which gives ca. 13000mAh at 1kg battery weight.
Now using a cheap 6s-50A ESC (must be ok quality because it draw easy over 60A!
With an aperage draw of 7-10 amp I may get 1,5 hours flighttime cruising at 50-60 kph.
Servos are 9 and 17g metal gear digital servos.
Inside there is an CUAV Pixhack Nano to control flight.
Setup with Arduplane software.
For now I am using A FrSky Taranis radio with a R9M 900mHz long range module to transmit, and a R9 long range receiver. To adjust parameters i use 3DR clone telemetry radios on 433mHz to not interfere with the control system. They have a quite short range of 3-5km.
I also have a pitotube to measure airspeed and so to be sure to keep enough speed in windy conditions.
A GPS is also a must have. This give a relieable speed, position, heading and altitude.
I am not using a compass because it causes very often problems in an plane with lot of magnetic interference from motor and power wires.
The GPS gives more than good enough heading.
Now when maiden flight is done, I will install a Hawksky Firefly 8s 90degree 4K action camera on an stabelized gimbal in the nose of the plane. This will be controlled via computer and telemetry link.
It will also be installed an Raspberry Pi 3B+ with UAVCast software. This and a Huawei E3372 LTE dongle gives me highspeed telemetry and videolink over the LTE network.
That should cover most of the equipment in my Talon
Morten.
Pilot: Morten M
Behind Camera: Elna And Bengt
Camera: Panasonic GH5
Drone: Mavic Air
Edit: Adobe Premiere with some color grading.
Instagram: @ArcticRc
Facebook: /
Email: [email protected]
Address:
Bengt Arntsen
PB 212
9770 Mehamn
FINNMARK
NORWAY
Morten was in a bit hurry so he forgot the canopy and the wires for he's home made and 3D printed gimbal so this flight is just to test out all the stuff he has mounted inside the plane.
Mortens setup:
X-UAV Talon specs:
1718mm wingspan
1100mm length
Usable flying weight up to 5kg. Would not recommend handlaunch over 3,5kg
Motor Sunnysky 3525 880kv with 12x6 propeller. Powered by a 5x4 (5S-4P) Panasonic NCR18650B LiIon batteries which gives ca. 13000mAh at 1kg battery weight.
Now using a cheap 6s-50A ESC (must be ok quality because it draw easy over 60A!
With an aperage draw of 7-10 amp I may get 1,5 hours flighttime cruising at 50-60 kph.
Servos are 9 and 17g metal gear digital servos.
Inside there is an CUAV Pixhack Nano to control flight.
Setup with Arduplane software.
For now I am using A FrSky Taranis radio with a R9M 900mHz long range module to transmit, and a R9 long range receiver. To adjust parameters i use 3DR clone telemetry radios on 433mHz to not interfere with the control system. They have a quite short range of 3-5km.
I also have a pitotube to measure airspeed and so to be sure to keep enough speed in windy conditions.
A GPS is also a must have. This give a relieable speed, position, heading and altitude.
I am not using a compass because it causes very often problems in an plane with lot of magnetic interference from motor and power wires.
The GPS gives more than good enough heading.
Now when maiden flight is done, I will install a Hawksky Firefly 8s 90degree 4K action camera on an stabelized gimbal in the nose of the plane. This will be controlled via computer and telemetry link.
It will also be installed an Raspberry Pi 3B+ with UAVCast software. This and a Huawei E3372 LTE dongle gives me highspeed telemetry and videolink over the LTE network.
That should cover most of the equipment in my Talon
Morten.
Pilot: Morten M
Behind Camera: Elna And Bengt
Camera: Panasonic GH5
Drone: Mavic Air
Edit: Adobe Premiere with some color grading.
Instagram: @ArcticRc
Facebook: /
Email: [email protected]
Address:
Bengt Arntsen
PB 212
9770 Mehamn
FINNMARK
NORWAY
Rcreviews.lt is not the owner of this text/video/image/photo content, the real source of content is Youtube.com and user declared in this page publication as Youtube.com user,
if you have any question about video removal, what was shared by open community, please contact Youtube.com directly or report bad/not working video links directly to video owner on Youtube.com. Removed video from Youtube.com will also be removed from here.
Advertising